Click here to check out the new BoatQuest website. New design, mobile and more! ➥

Related Searches

1979 36 (ft.) Pacemaker 36

Save This Ad

General Information

Listing# 133893

Price
$48,000.00
Location
West Dennis, MA, United States
Manufacturer
Pacemaker
Boat Type
Powerboat
Model Year
1979
Category
Sports Fishing Boats
Model
36
Status
Used
Length
36 (ft.)
Beam
159
LOA
432
Hull Material
Fiberglass
Fuel Type
unleaded
Engine Model
454
Number of Engines
2
Engine Type
Other
Engine Hours
870

General Details

SELLER UPDATE: "FREE WINTER STORAGE IS INCLUDED WITH THE VESSEL."

"Sea Es Cape" is a 36' Pacemaker Sedan Sportfish built in Egg Harbor NJ.
This model is a desirable one stateroom with adjoining head, with shower. The very large V berth has a filler cushion that forms a spacious double. The cabin has a large hanging storage closet and upper storage and shelves as well. All cushions, carpet, head liner and paint have been restored or replaced. There is an overhead hatch for fresh air if you choose not to use the dual Cruisair AC units, new in 2004. There is access to the chain locker from the Master stateroom as well.
The ensuite head is located forward of the galley to port. The combination head and shower feature new shower curtain, new shower head, rebuilt control valve, vinyl waterproof wall covering and new curtains.
The plumbing upgrades include new macerator motor, odor proof hoses and a new 35 gallon holding tank. The tank has excellent cleanout access and is fresh water rinsed.
The large galley features an apartment sized fridge (05), microwave oven and 3 burner range and oven combination (immaculate).
Storage abounds in the galley and there is a large double stainless steel sink.
All of the beautiful teak interior has been refinished with three coats of Silken color and three coats of high gloss clear coat. This includes the parquet cabin sole throughout.
Opposite is the dinette in the classic booth style. The dinette converts to a double and has roomy storage lockers below, as well as a large mirror and new coverings.
The main salon features a beautiful large sleep sofa to port, (04) with 12" air mattress.
that sleeps 2.
To starboard is a swivel chair, three set of teak storage cabinets and a full electrical panel as well. Forward in the salon is a wetbar with sink and two more teak cabinets.
The salon is bright and airy with the two large forward facing fixed windows and sliding windows to port and starboard. This is complimented with the large sliding glass door that leads to the cockpit. All of the windows have been removed and refurbished, tinted and re-bedded. All carpet, valances, curtains and headliner have been replaced in the last two years.
The cockpit features a solid teak deck, and fresh water wash down system. There are four rod holders, and new coaming pads with excellent access to below decks.
There is a fiberglass swim platform with Weaver Dinghy Chocks and outboard motor mount.
Ther is a stainless ladder to port with teak treads that leads to the Fly Bridge.
The bridge has a helm seating for three or four and storage under with cushions replaced in 04. The centerline helm extends all the way to starboard with all gauges including, Tachometer, Volt Meters, Temperature, oil pressure and hour meters. Some gauges have been replaced.
Electronics and navigation features include, Ritchie Compass, Raytheon 24 mile radar, with GPS integration and Raytheon Magnetron, Garmin 215 GPS that inter faces with radar. There is a Uniden 525 DSC VHF with MMSI # that is integrated to GPS and a Garmin 300C Color Fish Finder, depth sounder, voltage output, and engine synchronizer.

Cruise Speed- 16 knots at 25-28 GPH at 3350 RPM

Please submit any and ALL offers - your offer may be accepted! Submit your offer today!

We encourage all buyers to schedule a survey for an independent analysis. Any offer to purchase is ALWAYS subject to satisfactory survey results.

Take a look at ALL ***86 PICTURES*** of this vessel, AND A VIDEO, on our main website at POPYACHTS DOT COM. At POP Yachts, we will always provide you with a TRUE REPRESENTATION of every vessel we market. We are a full-service brokerage company, ready to assist you in purchasing any boat anywhere! Please allow us to be your eyes and ears on the ground and assist you with your next vessel purchase. Thank you for visiting and we look forward to speaking with you!

Stock #27862

Specifications

Condition
This vessel is in excellent condition, and there is a full detailed mechanical update document available. TONS OF UPGRADES - You won't find a boat that has been taken care of like this! Along with everything else in the listing - Below is all the most recent upgrades. Head Upgrades 2003-Head removed and rebuild- 100% new hoses, Macerator motor, joker valve, clamps, gaskets etc- $340.00 2007- Complete new holding tank removal and replacement with 35 gallon plastic tank, new Y value and all new hoses from deck fill to intake and our take. - $800 2002- New faucet- $150 2005- Rebuilt Shower assembly and hoses- $100 2001- New Shower Sump and hoses-$150 2008-New Vinyl wall coverings-$250 2008 New 12volt Compact Fluorescent lighting added to existing- $200 Other Upgrades Front Windows, Port and Starboard windows, all ports removed and re-bedded- NO LEAKS 2002- Window Shield Cover- $190 2003 All new Bridge Cushions- Captains Bench Seat, Cushions in front of Bridge Station- $1017 2003- 100% of all Lee Outriggers and hardware removed, re-chromed, re- wired (outrigger cables) and rebedded during installation- $650 2009 New Dual Trumpet Horn- $229.00 3 Deck Chairs 2004- New 2000 GPH Mid Bilge pump with auto on switch -180.00 2009 new 1500 GPH Aft Bilge pump with auto on switch bilge and hose- $125.00 Full Canvas Cockpit cover- $3000 Full Winter Bridge cover-$1500 2008 Full, 4 sided, Flying Bridge enclosure had all windows, zippers, Velcro, snaps all replaced with Strata Glass and heavy gauge plastic. - $1280.00 2008 Custom Cockpit shade made- GSC Marine- $653 Annually- Ablative Bottom Paint Applied All new Shaft, Rudder, Trim Tab, Hull and Heat Exchanger tank Zincs installed annually Complete Hull Deck Super Structure Wax Engine Oil! Filter Change every 50 Hours or season whichever comes first Boat is Dry stored 6 months per year with cover. Boat only runs 25-40 hours per season 7-19-2010 Updates Fall 2009 / Spring 2010 Upgrades: Port and Starboard Motors Oil and filter change with 6 Qts. Of Peak 10-40 oil 2 PH8A Oil Filter 276 Hours- Starboard 280 Hours Port- $80.00 4 Gallons anti freeze flush- $60.00 1 quart marvel mystery fluid fog- $7.00 AC Units- Full fresh water flush and winterize-$29.00 Holding tank- Drained, flushed with fresh water, pumped cleaned and air dried. All water systems Flushed and winterized with Non tox anti freeze. Fuel tanks filled and 1 16 oz bottle of Startron Ethanol per tank designed for 175 gallons per tank- $32.00 Generator Anti Freeze flush and re- fill Oil change with 3.5 qts Oil Anti Freeze winterize with Marvel Mystery fog-$60.00 Fuel System- 2 new Racor 3228SUL Fuel and water filters and separators-$79.90 New NAPA Fuel Canister and filter- NAPA 3271 filter $15.95 Generator- New Napa 3110 Fuel filter-$12.95 Sherwood E35Raw water pumps- Removed cleaned and installed new 10615K Sherwood Impellors and gaskets.-$84.90 Inspected all belts and replaced as needed. Touched and tightened all hose clamps Install 25 feet LED 500K 12 volt rope light under gunwales. New 12 volt switch Cleaned coaming, re tie wrapped all wiring, sealed all screws and wiring-$185.70 6.49 Installed new Fly bridge Storage door latched- $8.95 Installed new port side (red) LED running lamp and re sealed and re-bedded lens and lamps holder- $18.95 Cleaned, sanded and painted re bilge, Re Installed all copper bonding stripping-$49.95 Port and Starboard sides-Rudder posts and bolts and Strut Bolts and hardware.-Removed per side 4- 8 inch bronze Rudder bolts and knocked them out. Removed all rudder bedding and potting material per side. Re-bedded with Life Under water caulk. Re bolted rudder posts with new washers and nuts where needed. Re connected copper bonding stripping under rudder posts and thru hull and zincs- 10 hours- $350.00 New 20 X 12 inch Taylor Made Fenders wit new rope-$189.95 New Engine and AC Water heater room Fluorescent Lighting- 2- 14 watt, 12 volt on/off switched fixtures, and 1-30 watt, 12 volt, on /of switch fixture installed with 25 feet 12 2 wire connected to Engine room light switch in panel-$159.95 Interior- Replaced MR16 50 watt over head lamp with new 12volt- 5 watt LED lamp- $29.95 7-24-2010 Starboard Motor-292 hours New Mercury Mercruiser Oil Cooler Installed- Part # 63832T- 12 inch oil, 1 1/4 diameter connector oil cooler- $313.13 Installed all new 1 1/4 Trident hoses and clamps from Transmission U Cooler to Oil Cooler and Oil cooler to Heat exchanger. New Exhaust Manifold to Heat exchanger Trident hoses- 10 fee hose at 10.99 ft- $116.77 Changed engine oil and filter- Castrol 10-40 and Fram PH8 oil filter- $24.99 Port Motor-290 hours New En Dure Oil Cooler Installed- Part # 1132-12-7- 12 inch oil, 1 1/4 diameter connector oil cooler- $210.00 Installed all new 1 1/4 Trident hoses and clamps from Transmission U Cooler to Oil Cooler and Oil cooler to Heat exchanger. New Exhaust Manifold to Heat exchanger Trident hoses- 10 fee hose at 10.99 ft- $116.77 Changed engine oil and filter- Castrol 10-40 and Fram PH8 oil filter- $24.99 Replace 10 feet Remote oil filter to oil cooler and return oil cooler hose and clamps- NAPA H 1946- $39.53 7-28-2010 Sherwood E35 Raw water pumps- Complete rebuild of 2 SPARE Sherwood E 35 Raw Water Pumps with Major kit including all bearings, bushings, clips, impeller, gaskets bolts etc- $208.75 each x 2- $417.50 8-4-2010 Installed 200 feet 5/8 anchor line with new shackles- $278.00 8-12-2010 Port Motor- 292 hours New Mercury Quick Silver Fresh Water Pump assembly- 7.4 liter 454 GM big block-$209.31 Removed, cleaned and rebuilt thermostat housing. New upper and lower gaskets and sealant. New 165 degree Thermostat- $45.98 Drained engine block and heat exchanger of all anti-freeze. Removed Heat exchanger end caps and cleaned raw water cooling tubes with pipe cleaners Removed and Cleaned end cap gaskets and zincs Refilled Heat Exchanger and engine with 3 Gallons Napa full strength anti-freeze and water 50/50 mix- $39.80 parts and 5 hours labor. 10-31-2010 Winterization: Drain Fresh Water Tank Pump 8 Gallons -50 Non Tox Anti freeze through all fresh water systems including: Galley Sink and drain, Head Sink, Shower and shower sump, Head into holding tank and over board discharge, Salon Wet Bar sink, Fresh water wash down, dock side fresh water connection, engine room fresh water supply, Forward bilge pump. Air Conditioning System- full run and cycle 4 gallons anti freeze through the complete AC circulation system Engines and generator- 4 Gallons each engine flushed with fresh water for 15 minutes then run 4 gallons of 50/50 antifreeze is run through the motors and generator. All soft good are removed each year and stored at home in heat environment. All cushions have the zippers opened and sprayed with Fa-Breeze and stored in open air condition. $110.00 Jan to May 2011 project: Propellers- Both Port and Starboard Propellers were removed by Ship Shops and shipped to H and H Propeller for complete re-conditioning- Reconditioning- $285 each x 2= $570 New port side, brass prop nut- $10.00 Ship Shop Labor to remove and re-install- B Walsh- Propeller shaft transmission coupling was unbolted from Transmission. 1 3/8 Propeller Shaft and Transmission coupling removed and sent to Turnwright Machine Works for complete recondition of the propeller shaft and re-face the coupling. The shafts were magna-flexed and tested for bends, cracks and or any other potential problem. There were no crack reported and some small, minor, not uncommon bends discovered, which were corrected and put back into specification requirements. 8 new New Grade 8 fine thread bolts, lock washers and nuts were purchased. New Shaft coupling square keys, bolts were purchased and lock nuts vs. using the SS safety wire $360 plus $30 for the nuts, bolts washers and misc hardware. $390.00 Port and Starboard, Front and Rear Cutlass Bearings removed and replaced with new by Ship Shops- $4,700.00 Port and Starboard Front Motor mounts removed and replaced Crusader Engine Mount Part # 97926- $38.50 each x 4= $154.00 Port and Starboard Front Motor mounts support brackets removed and replaced Crusader Part # 97938- $45.50 each x 4= $182.00 Port and Starboard Front Motor mount ships removed and replaced with Aluminum shims- $30 each- 120.00 Ship Shops- Complete Port and Starboard engine Re Align with port and starboard propeller shafts, shaft coupling and transmission couplings. Ship Shops $ 270.00 Standard P and S side Stuffing Boxes with 2 1/2 inch stern tube and forward hose connectors with 2 nut packing gland removed. New PSS Drip-less Shaft Seal Kits purchased and installed- Part # 02-138-212= 1 3/8 shaft seal with 2 1/2 inch stern tube seal kit - H and H propeller- $237.50 each x 2 = $475.00 PSS seals require 1 inch of compression Safety measure- 1 3/8 shaft zinc collar installed in front of PSS seal for safety-$49.00 4 AWAB Clamps per PSS installed- $65.00 Plumbed with 3/8 high pressure hose and water tapped from exhaust elbow-$75.00 Total bilge area scrubbed and cleaned with a heavy duty degreaser and wiped clean- 6 hours time. Complete bilge area cleaned, degreased and painted with 2 gallons of White Bilge Cote- $69.99 per gallon x 2= $140.00- ( appx. 10 hours painting time) Port motor- both risers elbows and Vetus exhaust hose and clamps installed- Osco Part #- 8068 3 Inch Exhaust Elbow- $108.95 each x 3= $326.85 BAR- 4 Inch Riser- CR-20-97772- $111.95 x 3= $335.85 All slotted gaskets for fresh water cooled motor- $ 55.35 2 OSC799-K- Exhaust Manifold gasket kit and bolts- 12.85 x 2- $25.70 Starboard Motor- Starboard side Manifold removed and replace with new Osco Exhaust Fresh water cooled Exhaust Manifold Osco mounting kit with gasket and all bolts- OCS 7772MK- $67.10 Crusader Exhaust Manifold- Part # OSC 7992- $351.00 Port Engine- Both Exhaust Risers and Elbows and all corresponding gaskets, hardware, plugs and hoses removed and replaced wilt new. Starboard motor inside manifold Starboard Motor- outside Riser and elbow replaced in June 2010. All above exhaust risers and elbows removed. All hardware, nuts, bolts, hoses etc replaced and/or cleaned. All exhaust hose ends cut off for all raw water and fresh water hose ends cut off and mated new surfaces of all replaced parts. All new clamps where needed. Starboard motor- Re moved and replaced all 1 1/4 Trident exhaust hose with new-$15 ft-$150 Vetus SLANG75 3 Inch ID Exhaust hose replaced- 18 feet at 22.49 ft- $404.82 10 new AWAB 3 inch exhaust hose clamps- $68.00 Starboard motor outside- Exhaust manifold removed and gasket and bolt set replaced. 15 feet Triton Wet Exhaust Water hose 1 1/4 inch- 10.92Ft= $164.25 Port and Starboard Engine Anti Freeze flush- 6 gallons NAPA full strength antifreeze- $$50.97 16 new Spark plus installed- NGK- _______________ Napa part # 2623- $37.23 10 sheets Oil absorbent pads placed in engine compartment. All new shaft, rudder, hull and trim tab zincs- $140.96 2 Gallons West Marine PGA Gold Ablative bottom paint-$169.99 per gallon-$339.98 P and S Side Racor Fuel Filter- S3228TUL- $39.99 each- $79.98 12 each 7 and 8 inch x 1/2 lag Motor mount bolts removed and replaced-$35.40 Generator- 8 feet Exhaust manifold to muffler exhaust hose replaced with Trident 1 3/4 hard wall hose-$85.00 New Onan Impeller and gasket- water pump removed, cleaned and verified for operation-$45.00 New Red heater hose for coolant and water intake replaced- $15 ft- $60.00 Stern Bilge Steering System Compartment- Steering and rudder gear platform, originally made of standard plywood was cut out and replaced with 3/4 ASTEK Plastic wood. Mounted on the Platform the following was removed, reconditioned or replaced with new- Steering cable assembly removed, Turn stop plate removed, Port and Starboard Rudder Bearing Flange removed and replaced with new 1 5/16 cast Pillow Bearing. Rudder removed and Rudder stuffing box nut Replaced with 1/ 4 packing Rudder nut, 4 RINGS OF 1/4 inch Teflon packing removed and replaced. - $125.00. Starboard Side Trim Tab- 8 (all) Bolts, nuts and washers removed. All old bedding removed and cleaned. Re-bedded all holes and replaced all nuts, bolts and lock washers.-45.00 Rear Steering/ Bilge Area- cleaned and re-painted complete rear bilge and all storage area- Pettit marine white epoxy Bilge paint- $69.99 gallon All Salon floor boards and hatch removed and conditioned: 2 Piece Center Engine access hatch Port and Starboard side floor boards- 4 pieces total Generator Hatch All nails, staples and misc hardware removed and reconditioned. All carpet removed from the floor board and was sent to Paramount Carpet Cleaners for professional cleaning including the complete salon carpet and stair carpet- $125.00 All new rubber based carpet pad custom cut and stapled to each hatch and stapled with stainless steel staples. Carpet re-installed and re-stapled with Stainless steel 5/ 16 staples. $150.00 5-2-2011 Fly Bridge Gauge assembly- 2 New Teleflex Morse Analog Water Temperature gauges installed for both Port and Starboard engine- 12V, 20-240Degree Part # 57904P $75.50 Complete bottom scrape and sand Buff props, shafts, rudders, trim tabs 2 coats of Petit Ablative bottom paint 4 1 3/8 shaft zincs 2- 5 inch rudder zincs 2- 5 inch trim tab zincs 2 hull zinc plates 2011 BW-Job Total hours and parts cost - $2900.00 Ship Shops Labor Costs- $4,950.00 5-25-2011- New Starboard Cranking and starting battery NAPA with 30 month warranty-$69.17 7-10-2011- Port Side Salon/Cockpit Bulkhead- complete cut out and removal of the Bulkhead from the top of the bridge deck to 12 inch above the cockpit floor and across the complete width. Custom cut and installed 3 layer's of 3/4 inch (Three Quarters of an Inch) Marine Plywood= 2.25 total inches of marine plywood installed. 2 of the 3 layers- (outside layer and Middle were coated with 2 coats of West Marine fiberglass resin. Each layer installed/sandwiched in the middle with 3M 5200 and screwed to each other and all side with Stainless steel screws. Each layer then gap filled with 3M 5200. 8 tubes 5200, Plywood and Misc supplies- $300.00 Top Layer professionally filled in, flared, sanded with marine fill then fiber glass coated by Jannery Marine service.- $350.00 Final Finish- Top Coat and finish- 2 quarts of 3M Gel Coat White applied to the complete (both sides) bulkhead. Bulkhead was sanded, prepped and top coated. All seams caulked with marine Silicone- $101.48 TOTAL LABOR HOURES- 22 HOURS. 8-1-2011- Mid Bilge Pump- Complete new RULE 2000 GPH Bilge with RULE Matic auto bilge pump switch installed. All new wiring, filled in all old mounting holes and drilled, sealed and installed new strainers- $180.96 8-30-2011 Hurricane Irene Boat While Hauled- Complete Bottom Power wash Complete Bottom scrape and re-paint with West Marine PCA Gild Ablative - 2 gallons- $169.99 per gallon-$339.98 4 New Rudder and Trim Tab 5 Inch Martyr Zincs plus 4 1 3/8 Shaft zincs- $116.82 New Dinette table covering with new Formicas Wilsonart Laminent Mesa Gold $197.69 11-2011 Winterization: Drain Fresh Water Tank Pump 8 Gallons -50 Non Tox Anti freeze through all fresh water systems including: Galley Sink and drain, Head Sink, Shower and shower sump, Head into holding tank and over board discharge, Salon Wet Bar sink, Fresh water wash down, dock side fresh water connection, engine room fresh water supply, Forward bilge pump. Air Conditioning System- full run and cycle 4 gallons anti freeze through the complete AC circulation system Engines and generator- 4 Gallons each engine flushed with fresh water for 15 minutes then run 4 gallons of 50/50 antifreeze is run through the motors and generator. All soft good are removed each year and stored at home in heat environment. All cushions have the zippers opened and sprayed with Fa-Breeze and stored in open air condition. $110.00 Engines- Post and Starboard- Each engine run for 15 minutes to warm up. 6 Quarts of old oil pumped out of each engine. Fram PH8A filter removed and replaced plus 6 qts Castrol 10-40 oil. Generator Oil change with 3 qts.Castrol 10-40. 4-22-2012 Custom Canvas Complete new Flybridge Enclosure: Material- Stamoid Cream Vinyl, All new zippers, all new snaps, all new windows, all on boat snaps and buttons on the boat were removed, sealed and re-fitted with 3M 5200, Stainless Steel enclosure frame- all rivets drilled out, removed and re-riveted $4,568.75 Plus cost for material- new snaps, buttons, 3M, ect- $ 250.00 New Front Starboard window cover $175.00 5-12-2012 Re Launch Prep Bottom power washed, sanded where needed and scrapped- Due to August compete re bottom pain installation all hulls side below the water line a, struts, shafts, rudders,, trim tabs and all scrapped down and sanded areas repainted and touched up with Petit Horizon Black Ablative bottom paint. Port and Starboard engine intake screens, Generator and Head intakes screens removed and bodies scrapped to bare metal. All outer intale seams removed all old caulk down to the bare metal and fiberglass and Re caulked with 3M 5200, repainted and all new Stainless steel hardware to install water screens installed. Shafts and props polished to bright SS and Brass finish- materials $35.00 Rudder and trim tabs- 5 inch zincs installed- $26.55 each= ` $106.20 Shaft zincs 4 1 3/8 inch zincs installed. @ 16.28 each= $65.12 Hull Zinc installed- $28.57 Outriggers Wet sanded with polishing compound and 600 grid wet sand paper. Polished and waxed along with the Chrome mounting hardward. West Marine Under water 6 LED lights installed. Mounted 1 LED under water light on the outer edge of the trim tab lip ends. Drilled 3 holes in each trim tab and installed with Nut and bold configuration each light. Wired path is under the swim platform using water proof connections with silicone sealant. Light are wired into the cockpit LED rope lighting switch. Each lamp-$50.00 x 2 = $100 plus wire and labor= $156.00 Generator- New Onan exhaust water cooled manifold Part # 100-1058. Installed with all new brass pipe fitting's- $176.00 Sherwood E35 raw engine pumps- 2 new, Port and Starboard impellor installed- $98.00 Sierra In Line Fuel Canister and Filter Port and Starboard- $29.95 Each x 2= $59.90 Water Fuel separators- 3228UL filters installed-$39,99 each $80.00 Deck Shade mounts removed and backing plates replaced with plastic backing plates. Silicon sealant and new screws- $12.95. 5-21-2012 Port Engine Complete Head Rebuild and all parts components replaced and or cleaned to as new condition including the following: Port Engine Cylinder Head Rebuild 5-20 to 6-3-2012 333.4 hours on port bridge hours gauge Disassembly Carburetor removed and cleaned Gas line disconnected Electronic Distributor removed- set and re timed to cylinder #1 Wiring- White with black strip to water temp sending unit Dual Orange and red wire to thermostat alarm replaced from oil temp gauge to high temp alarm. Main wiring harness re routed and re wrapped Throttle cable disconnected Spark plugs removed And replaced with8 new NGK BR6 gapped to .35 Coolant drained and replaced on re build with 4 gallons Peak antifreeze and 4 gal water Flush and clean heat exchanger New heat exchanger end cap gaskets and seals Test pressure cap Oil drained and replaced with Oil filter and Fram PH 8A filter removed and replaced Oil pan filled with marvel mystery oil and drained. Intake manifold removed ground down and repainted All raw and coolant water hoses removed and replaced as needed. Exhaust manifolds port and starboard removed and replaced with 100% new parts Risers and elbows removed complete cleaned and regasketed on refit Oil cooler removed Removed the port and starboard cylinder head for 100% Rebuild Port engine starboard side head casting # 11875 Port engine port side cylinder head casting # 01077 Removed the valve cover, cleaned and repainted Removed the intake manifold, cleaned and painted New intake gaskets Electronic distributor removed cleaned and reinstalled Complete new FelPro gaskets set including head gaskets, intake manifold, distributor, exhaust manifolds replaced. Mid Cape Machine Shop. $1146.75 rebuild - $650 labor and $496.75 parts Parts needed- for complete Port motor cylinder head rebuild. Rebuild- complete rebuild with all new parts 8 new intake stainless Steel valves 8 new stainless steel exhaust valves 16 new valve seets 16 new valve springs All intake and exhaust ports re ground and seethed Rebuild heads with complete magna flux, re surface each side, check for cracks, inspect intake and exhaust valves, inspect and check valve rings, complete clean and test heads. Push rods tested and checked for true and tested good. Cylinder head bolts tested and cleaned. Torqued to 80 lbs plus 1/4 extra turn and sealed with gasket sealant Ship Shops Mechanic Alex installed heads, intake manifold and distributor. 3 hours- $285.00 Values adjusted and tested. Head gaskets replaced and included with gasket kit from head rebuild Intake manifold gaskets set included with head rebuild. Intake manifold bolt set 13 Grade 5 with flat washers set. Tongue to 40 lbs. Checked head bolts ok Mid Cape machine Checked push rods ok Mid Cape Machine. Thread sealants send on all bolts except head bolts $4.50 Battery cable end 1/4 to 3/8 I ID lug. $3.00 1 case oil $ 50.00 4 gallons anti freeze and 4 gallons water $62.00 Transmission fluid hose end $ 17.00 6 feet trident 1 1/4 hard wall hose $ $40.00 Port and starboard side exhaust manifold with no spacer Starboard Osco 7992 209.95 Port side Osco 7993- 213.95 Osco water 1 1/4 inlet x 2 - 12.95 4 1 slot gaskets for exhaust manifold Barr 96562 2.45 x 4 = 9.80 2 stainless steel block off plate Osco 97296 6.00 Gaskets set up for exhaust manifold to riser -1 slot 1 SS block off, 1 slot Port side Mounting kit for exhaust manifold to riser 7772 MK mounting kit is for NO Space $34.95 97296 stainless steel block off plate 1 have 1 need 1 $35.00 each x 2 = $70.00 1 hole gaskets I need 4 Barr 96562 @ 2.45 each x 4 2 valve cover gaskets Included with gasket set from head rebuild. Sealed Starboard side Exhaust manifold mounting kit 1 MK 7992 MK - 34.95 Napa gold canister and filter gas filter set port and starboard replaced $ 58.00 3228Ul rancor water fuel separator x 2 4 cans blue crusader spray paint. - 9.95 8 spark plugs NGK BPR6FS Fel Pro head gasket kit 17240 for Oval Port included head gasket, intake manifold gaskets, valve cover gaskets-377.00 Complete engine repaint- $45.00 Engine retimed. Engine started and checked for all above installed parts and leaks. No issues or leaks.. Total Port Engine Rebuild- $2162.75 7-10-2012 Starboard Engine- New NAPA Oil Pressure Sending switch- part # 18-5899- $31.50 New NAPA Oil pressure alarm switch- OP6619- $9.00 Onan Generator- Pump housing # 170-3172 Raw Water Pump complete rebuild- Onan KIT part # 131-0257 New impellor and gasket New Stainless Steel Impellor shaft assembly with 2 bushings New snap rings x 2 New Seals New Spring seal New Wear plate 131-0257 Parts Kit- $309.65 New 12 volts 20 amp toggle switch for navigation lights- $3.33. 10-5-12 Port and Starboard- 6 Qts Castrol Oil and Fram PH8A Oil Filter $56.50 Coolant top off Transmission top off Onan Generator- Oil change Full winterization Full heavy power wash bottom 5-8-13 Pre Commissioning Tighten all hose clamps, check all fluids, tighten all belts, inspect all nuts bolts etc. inspect all components Starboard Engine- Starboard side - Remove Riser and elbow- Clean and replace exhaust manifold gaskets between riser and manifold $25.00 Replace Racor Water fuel filters- S3228TUL Inspect water pump impellers- Both P and S Impellers replaced May 2012 with less then 20 hours on each Complete bottom scrape and sand Buff props, shafts, rudders, trim tabs 2 coats of Petit Ablative bottom paint $321.50 4 1 3/8 shaft zincs 2- 5 inch rudder zincs 2- 5 inch trim tab zincs 2 hull zinc plates $158.82 Removed and replaced under warranty West Marine Under Water LED Trim Tab lights- Over $100,000 has been invested in upgrades in parts and material, not including labor, over the past 11 years, with most of these upgrades being completed by the very knowledgeable owner/mechanic. If you add in the labor there world have been at least an additional $100,000 invested in labor as the owner has invested at least 1600 hours completing these upgrades. There are 8-3 ring binders with all documentation, receipts, part numbers, manuals and installation dates and hours of all listed work above.