Related Searches

2010 28 (ft.) 8 (in.) Commercial /Remote power Front Gate

Save This Ad

General Information

Listing# 26248

Price
$72,000.00
Location
Unknown, MO, United States
Manufacturer
27'6" Jet Powered Aluminum Landing Craft
Boat Type
Powerboat
Model Year
2010
Category
Barge
Model
/Remote power Front Gate
Status
Used
Length
28 (ft.) 8 (in.)
Beam
8.33
LOA
27.67
Fuel Type
unleaded
Number of Engines
1

General Details

2010 27'6" x 100" x 18" - 20" Jet Powered Aluminum Landing Craft

Length over all (LOA) = 27’ 6' (includes 30” rear swim deck)

  100” Beam width, 8” Formed Gunnel top (1 PART)

  48” X 144” X 0.250” Super heavy duty 5086 center keel plate 

 

        (3) Three Independent Air Chambers

  Sealed self bailing work deck with rear scupper doors

 

  Heavy duty remote power front gate with 2000 lb capacity

  24” Vertical from work deck, 0.125” 5052 Pre-Flex formed gunnel    one

part sides

  Full length 3” side collision guard structurally attached to side to air

chamber seam

  Front deck: 12' 6" from front of helm tower to base of bow door

  85” wide between gunnels where there are no bow compartments

  Load Capacity: 2550 lbs.

  Heavy duty bow entry keel doubler plate  (0.375” total thickness)

  Two part motor cover / driver seat

  Draft: 18" - 20” @ 5000 lbs. with correct center of gravity 

 

VORTEC 8100 V8 ENGINE 

Type:                 5.7L V8

Displacement:                     350 cid

Compression Ratio: 9.1:1

Valve Configuration: Dual Overhead Valves

Valve Lifters: Hydraulic Roller

Fuel System: Gaseous Fuel

Fuel Type: Regular Unleaded

Horsepower: 325 hp (292 kW) @ 4600 rpm

Torque: 450 lb-ft (682 Nm) @ 3200 rpm

Weight: 527 lb (330 kg)

Block: Cast Iron

Cylinder Head: Cast Iron

Intake Manifold: Cast Aluminum

 

 

SUPER DUTY JET DRIVE 

American Turbine Super Duty Jet Drive model SD-312

Designed for boats up to 7500 pounds all up weight

Driveshaft with sealed bearing housing to keep water out

Stainless steel pump shaft

Stainless steel impeller

 

BOW STORAGE - COMPARTMENTS

There shall be two (2) storage compartments located in the forward front

corners inside each bow compartment. Each compartment shall be designed

for quick access items required on the work deck. Ie. Bumpers, throw

pillows, life jackets.etc.

 

STORAGE BINS – MID SHIP GUNNEL COMPARTMENTS

81” L X 13.5” W X 16” H sealed storage bin provided under the forward

bench seating integrated into each of the forward gunnel tops.

 

 

BOW POWER GATE

Gate 72" wide. The gate shall be designed so the door opening is above the

water line, thus enabling the door to be opened

without water entering the boat. The gate is operated by standard manual

cable winch. Optional duel (2) Warn 1700 lb. electric winches or remote

hydraulics are also available.

 

STERN SWIM DECK

Swim deck approximately 30” long x 95” wide with skid resistant coating.

 

COVERED HELM

44" wide

Windshield with electric wiper

Hard top cover approximately 62" W x 98" L

Structural ladder system for access of the hard top cover

Drop down radio compartment approximately 18" W x 26" L x 7" H 

 

HELM SECURITY COVER

ROM roll up door to allow for access to operator console in the up

position out of the way of the operator and designed to lock in a lowered

position.

..

BILGE PUMPS

T(2) bilge pumps, one (1) 1000 gallon per hour pump located at the lowest

possible location of the engine compartment and one (1) 1000 gallon per

hour pump located approximately 36

inches ahead of the engine compartment bulkhead. Each pump equipped with a

float type switch to permit

automatic pump activation. 

 

INTERIOR  FINISH

The interior components of the boat hull completely covered with scorpion

commercial liner

In the color of grey, including:

- Gunnel tops

- Interior vertical side areas

- Bow compartments inside & out

- Hose bins inside & out

- Motor cover exterior, top & bottom

 

SCORPION PROTECTIVE LINER

All horiznon walking and stepping surfaces covered with Scorpion non-skid

liner. 

 

BOAT TRAILER - STEEL 

EZ Loader Trailer  Spare Tire Mount

Horizontal Side Guides

Precision Contoured Bunk Support System

Welded Tubular A-frame & Tubular Bunk Uprights

Urethane Coating System with Urethane Flex Primer

Diamond Plated Aluminum Fender Step

V-Camber Sprung Axle Powder Coated

Mc Guard Lug Nuts (Guaranteed Not to Rust for Life!)

Soft Marine Grade Carpeting on Bunks and Fender Pads

Two-Way Ratcheting and Free Spooling Winch with Strap

Plastic Coated Pre-Coiled Safety Cables

Disc Braking System

In-line Hydraulic "Surge" Brake Actuator

Quad-Bunk Support

Weld on Jack Stand

Trailer   GVW = 1300 LBS

Trailer GVWR = 6500 LBS

Trailer  MAX. LOAD = 5200 LBS

 

Located in Missouri

Price: $72,000 USD

Reference No. LC2095

Specifications

Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.
customContactInformation
Scruton Marine Services - File No. LC2095 Please contact Peggy Scruton at 519-583-1636 for further information